File Archive Upload Reminder!
Started by micro, February 01, 2015, 02:50:37 AM
Quote from: iVirtualZero on November 02, 2019, 08:22:42 PMHow do i install the DFO in an earlier model PS1 the one with the composite ports? PU-8 SCPH-1002 model.
Quote from: Damn-Deal-Done on July 15, 2020, 07:45:53 PMI don't get update notifications from the site.
Quote from: bmp02 on July 02, 2019, 10:14:29 PMPlease note the chip on the programmer needs to be flashed with firmware and fuse bytes. To do that, I bought the Micro USB Tiny AVR ISP / USBTinyISP Programmer (this one: https://www.ebay.com/itm/Micro-USB-Tiny-AVR-ISP-5V-ATtiny44-USBTinyISP-Programmer-For-Arduino-Bootloader/222053881584). It's 1.86$ including shipping, not too bad huh.Then download this driver (https://learn.adafruit.com/usbtinyisp/drivers) and the AVRDUDESS Gui (http://blog.zakkemble.net/avrdudess-a-gui-for-avrdude/) to flash firmware and fuse bytes.
Quote from: SilentEyes on September 30, 2020, 03:39:28 PMJust wondering, how would you install a DFO in a pu-7 board?
Quote from: SilentEyes on March 03, 2021, 08:02:54 AMHi provato,I know it has been forever since I posted in this forum lmao.First and foremost, How would I be able to wire the switch to my oscillator? I was thinking more like I take NTSC/3.3v from one pin of the GPU and then PAL/GND from another pin of the GPU and somehow wire them to the outsides of the switch and then the middle to the oscillator? My PU-7 does seem to only have 1 input. If you're saying that I need to wire the input of S0 the switch, I wouldn't really understand how to do that. I dunno, you're better than me at this. It seems that the newer models are easier cause they have two inputs that you can link to a second oscillator. In this case, I was thinking of wiring a 53.20mhz oscillator from a PAL ps1 that's broken, but I don't know where S0 would be on a hardwired pu-7. I know this is a lot lmao, I have lots of questions. Please let me know.Thanks!
Quote from: SilentEyes on March 03, 2021, 02:36:02 PMWell, too late now. I broke my pu-7
Quote from: Monkeyball on March 18, 2021, 06:03:52 PMI've had a DFO installed on my PAL 5552 model PS1 and I am having a strange issue with the console.My TV normally switches between NTSC / PAL modes automatically but on this occasion it is having issues syncing to the PS1 signalThe strange bit is the console is a PAL model with DFO but PAL games are not syncing correctly and if the TV does manage to lock onto the signal the colours come out wrong NTSC games are working normally though.I had the DFO installed so that I could have the games work with the correct colours in PAL / NTSC using composite cable.What do you think is going on?It works on a more modern TV KV-32FQ70U but not my primary retro tv SONY KV-A2942UThe TV in the video is in service mode and it gives an example of the problemhttps://www.dropbox.com/s/nq7zpme04u4qn9e/VIDEO0286.mp4?dl=0In the second video you can see it a bit clearer without the black rolling lines picked up by the phone camerahttps://www.dropbox.com/s/mj74auwwcfi40i8/VIDEO0287.mp4?dl=0I'm thinking maybe its an issue with the installation or the DFO itself as I understand it was made with modern TV's in mind?Maybe an older CRT needs different clock frequency timing?Btw what was the result of installing a 50/60hz switch on the 1002 model? I'm guessing that installing a switch will allow the TV to sync properly
Quote from: provato on March 19, 2021, 08:03:37 AMIt's not a mod for modern TVs only. It should work perfectly fine with ntsc 4.43 and pal 4.43 capable CRTs. Your monitors are indeed capable of both ntsc and pal (looked up the manuals).Use an RGB scart PS1 cable (to rule out subcarrier frequency problems) and see if the problem persists.If it does, then most probably it's an installation or a clockpro code problem.Which clockpro hex file have you written on the cdce**** chip, and which such chip are you using?
Quote from: Monkeyball on March 23, 2021, 06:21:00 AMQuote from: provato on March 19, 2021, 08:03:37 AMIt's not a mod for modern TVs only. It should work perfectly fine with ntsc 4.43 and pal 4.43 capable CRTs. Your monitors are indeed capable of both ntsc and pal (looked up the manuals).Use an RGB scart PS1 cable (to rule out subcarrier frequency problems) and see if the problem persists.If it does, then most probably it's an installation or a clockpro code problem.Which clockpro hex file have you written on the cdce**** chip, and which such chip are you using?Hi,It works fine through RGB Scart no issues at all but I do prefer to use the composite cableI purchased it from a website and unfortunately I am not getting much help from the seller so I thought to post here.To see what I can do to correct the issueThe chip is 3.3V SMD version I'll contact the seller to find out which clockpro hex file it is