X68KFDUINO - new adapter for external Floppy Drive for HxC & Gotek

[BlackVega]

I guess the board is supposed to be powered from the 4 pin header on the right side and gotek/hxc is also supposed to be powered from another 4 pin pass through header, although it wasn't completely specified.

Hey, please tell me how I'm supposed to configure software. I flashed the Raspberry Pico using Arduino IDE and I think it was successful but I still need to test it. However I'm completely confused on what I'm supposed to do to configure HXC itself. I don't have a Gotek but what I have is exactly the thing on the right:


What am I supposed to do? Am I supposed to flash it with Flashfloppy, proprietary software, configure it or use it as is??? I'm totally new to this idea and all of these websites are so confusing and I have absolutely no idea what to do here. Please help

[aotta]

In few words, the x68fduino goes between x68k via a 34 idc floppy cable (esternal with adapter or internal with modded cable), powered by a standard atx 4 pin floppy connector (even if 12v is not used/connected). On the other side of the x68kfduino, another cable idc 34 pin is connected to your hxc, and another idc 4pin f/f cable powers the HXC from the x68kfduino (that's why it has 2 power connectors and they're linked togheter). I usually disconnect or select as 2/3 the internal drive, because most of disks boot only from drive 0 or 1.
Then use HXC as usual configuring it for both drives, but use  buttons on x68kfduino to turn led on green if they're off or blinking.
That's all.

[BlackVega]

I tested my HXC hardware and thankfully it works on a real X68000. However how in the world do you emulate both floppy drives using HXC?? I figured out how to load an image into a single drive 0 but I can't figure out for the life of me how to load another disk into drive 1 so both images can be accessed by X68000 and that was pretty much my entire purpose for using this device (albeit an SSD solution even for 1 drive is still excellent). You know, you insert both disks into drive 0 and drive 1 at the same time to load games on X68000. How do you do that?

[aotta]

I tested my HXC hardware and thankfully it works on a real X68000. However how in the world do you emulate both floppy drives using HXC?? I figured out how to load an image into a single drive 0 but I can't figure out for the life of me how to load another disk into drive 1 so both images can be accessed by X68000 and that was pretty much my entire purpose for using this device (albeit an SSD solution even for 1 drive is still excellent). You know, you insert both disks into drive 0 and drive 1 at the same time to load games on X68000. How do you do that?

Pressing the middle button for 2 seconds you got a menu with the option "select drive a/b".. just select the other and assign it the second floppy's image.
It's all on HXC manual, of course...

[BlackVega]

Ah right, forgive me this is my 1st time using anything like this and I just didn't have energy to read tons of pages of that manual and I thought maybe that board was not functioning properly. Also that HXC website is no offense very confusing and so awful looking and super disorienting and it is very hard to read anything useful. Well, after all of that it looks like this board is working fine or at least I think it is. Both drives load fine but these buttons and flashes on the board are inconsistent. Many times both of them blink (even though only drive 0 should blink on the start) and many times I need to press both buttons to load single disk games for some reason and soft eject doesn't work, it should "eject the virtual disk automatically" but it just waits with black screen until I press on board buttons again and then it continues. What is up with all of that? Is this intentional? I still haven't figured out how to use it properly but even at this time it loads stuff successfully which is awesome. Hoping it will be improved later with perfect functionality. Great device for users with broken floppy drives!

I still have some more questions however- red LEDs never work for me and they only light up when X68000 is powered off. Also is LED_blink pin (internal pin 13-external pin 26) supposed to be connected or not? Because I can see a trace on the board but it's not there on the FDD adapter. Is this intentional or is it a mistake? And, after everything I've described, is my FDD board working correctly or it is pretty wonky sometimes at this stage? Aha and also if anyone wants I still have some extra boards so I can sell some boards and test them on real hardware if anyone is in the need

[aotta]

Yes sometimes leds seems crazy.. but it's becouse X68k sends ejects commands in strange ways, and i can't simply ignore them or games with more than 2 disks won't work. So, the game is to keep the green led on pushing button when the PC eject the disk when not needed!

Anyway, i did some minor changes and uploaded a version 1.0a on the repo, it seems a little more stable especially in my X68K with no floppies, that is the one in which X68KFDPico works worst.

[BlackVega]

I checked the new version and wow it definitely works better. Soft eject finally works and it's automatic! My X68000 no longer starts up with black screen and now it displays "please insert floppy" screen as it was before. However I'm still not sure why you almost always need to press "HD1" button whenever you load anything from drive 0. Is this a bug? Oh well, it still definitely works way better compared to before as it used to be glitchy as hell sometimes. I think it's almost perfect now. However I have a question- is 2x Gotek or 2x HXC more recommended than 1x HXC? Is this going to help or potentially bring it to 100% perfect functionality 1 day? I think this setup is good enough for me but I wonder whether I can benefit from using 2x Gotek devices. Thanks for creating this device, definitely unlocked full potential of my machine

[aotta]

My gadget handles X68k signals but sincerly i don't know their logic.. and i can't predict if you're using a single floppy or some sw that needs two, that's why i have to suppose that both floppy are ready at startup.
And, probably 2x gotek it's different from HxC solution, so it's not easy to improve further the SW.
I don't understand what you mean with 2x HxC, but i suppose you mean one HxC used for both floppies. That's with no doubt the better (even if not the cheapest) solution compared to two goteks, with less cables, a single psu connection and a single display to look into.
Yes, it's a pity that the switching from floppy A to B is not so smart in HxC, but it remains a great solution IMHO.

One last thing... since i use the great HDD image v.2.2 from @incrediblehark, I use floppy only to launch bootsec.x once on my X68Ks!   

[BlackVega]

Some games can only be run from floppies tho. Or is there a way to get around that?